D.O.A's 98 Sport / SRT Swap *Updated 08/06/08* With Vids!!!
- musclecarfan6
- 1GN Registrant
- Posts: 62
- Joined: Thu Jun 28, 2007 6:18 pm
- Location: Pittsboro,IN
The Wheels are Drag DR-17.
They are 15x7, offset unknown til I measure. They weigh about 13.5lbs I think? Flat black finish.
We picked them up at Discount Tire Direct when they were on sale for $69/wheel. It was a smokin deal I couldn't pass up.
The exhaust that WAS on there was a Vibrant I think, and we will be running just a downpipe on it.
They are 15x7, offset unknown til I measure. They weigh about 13.5lbs I think? Flat black finish.
We picked them up at Discount Tire Direct when they were on sale for $69/wheel. It was a smokin deal I couldn't pass up.
The exhaust that WAS on there was a Vibrant I think, and we will be running just a downpipe on it.
-> Chris <-
1998 SRT Swap Drag Car / 1997 Dodge Neon Coupe
1998 SRT Swap Drag Car / 1997 Dodge Neon Coupe
- musclecarfan6
- 1GN Registrant
- Posts: 62
- Joined: Thu Jun 28, 2007 6:18 pm
- Location: Pittsboro,IN
Major Updates!!!
1st off, we picked up an engine from a friend in NH. Its a nice low mileage SRT motor with a 3.55 Trans equipped with a Quaife already.
Then we ordered a fuel cell and SS brake lines from Jeg's. No pics of the brake lines, but you know what they look like! The fuel cell is a 5 gallon Poly tank with foam inside for drag racing.
Taping out the trunk to figure out where the cell will go:
Here is Jeff doing some cutting, WITHOUT the safety guard on, he sure is a rebel LoL
Look out Andrew!!! Jeff is crazy with that grinder!
Fuel cell is in place, just gotta find some straps to hold her in!
Ordered some parts to refresh the motor. Got some Unorthodox adjustable cam gears, new timing belt, new water pump and a new serp belt. We are only running an alternator so we had to find a custom length belt.
Old water pump with plastic vanes!!
Nice new pump, with metal vanes, interesting difference.
We borrowed an engine crane from Jeff's uncle so it was time to get the motor into the car!
We got all of our mounts sorted. Running a custom solid bobble, billet trans mount insert, custom built GreenBastard front mount as well as a solid billet pass side mount.
Needless to say, with little, well actually no play in the mounts getting everything buttoned up was not easy...
Andrew cleaning the engine bay up:
Motor on the crane:
Dad holding onto the crane while I cranked:
Starting to slide it in:
Finally
All the panels out front of the house:
We got the body panels sitting onto it for giggles. JDM hood tilt for now...
Thats all for now, next we will make sure everything is kosher in there and start to wire everything up, guess we should order the MS...
Thanks for looking guys.
1st off, we picked up an engine from a friend in NH. Its a nice low mileage SRT motor with a 3.55 Trans equipped with a Quaife already.
Then we ordered a fuel cell and SS brake lines from Jeg's. No pics of the brake lines, but you know what they look like! The fuel cell is a 5 gallon Poly tank with foam inside for drag racing.
Taping out the trunk to figure out where the cell will go:
Here is Jeff doing some cutting, WITHOUT the safety guard on, he sure is a rebel LoL
Look out Andrew!!! Jeff is crazy with that grinder!
Fuel cell is in place, just gotta find some straps to hold her in!
Ordered some parts to refresh the motor. Got some Unorthodox adjustable cam gears, new timing belt, new water pump and a new serp belt. We are only running an alternator so we had to find a custom length belt.
Old water pump with plastic vanes!!
Nice new pump, with metal vanes, interesting difference.
We borrowed an engine crane from Jeff's uncle so it was time to get the motor into the car!
We got all of our mounts sorted. Running a custom solid bobble, billet trans mount insert, custom built GreenBastard front mount as well as a solid billet pass side mount.
Needless to say, with little, well actually no play in the mounts getting everything buttoned up was not easy...
Andrew cleaning the engine bay up:
Motor on the crane:
Dad holding onto the crane while I cranked:
Starting to slide it in:
Finally
All the panels out front of the house:
We got the body panels sitting onto it for giggles. JDM hood tilt for now...
Thats all for now, next we will make sure everything is kosher in there and start to wire everything up, guess we should order the MS...
Thanks for looking guys.
-> Chris <-
1998 SRT Swap Drag Car / 1997 Dodge Neon Coupe
1998 SRT Swap Drag Car / 1997 Dodge Neon Coupe
-
- 1GN Registrant
- Posts: 129
- Joined: Mon Jun 18, 2007 6:45 pm
- Location: Toronto, Canada
fuckin right guys!! I didnt know u were this far into already... nice progress I thought she was just stripped.. so why didnt I check this out when I was over on sunday morninggg??? I'll be droppin by again sooon dudes
98 ACR SEDAN.. Magnum SOHC.. 14.46 @ 94MPH SOLD
98 Base Coupe, 2.4 SRT turbo @ 16 PSI.. 3xx whp 1/4 unknown
What made you decide to not use the SRT Waterpump? (the one with the plastic vanes)
It was designed that way to add more flow capacity. Just curious thats all
It was designed that way to add more flow capacity. Just curious thats all
06 Subaru STI WRB ~ BC Coilovers, Kartboy Bushings
98 Neon R/T 2.4L Turbo Coupe ~ Project car
2007 -Purchased and stripped
2011 -Needs a tune and minor things
02 Neon R/T ~ 08/08/08 -traded for the 07 Caliber R/T (03/14/11 -traded Caliber for STI)
---
http://www.st1ck3rs.com
http://www.detroitneonowners.org
98 Neon R/T 2.4L Turbo Coupe ~ Project car
2007 -Purchased and stripped
2011 -Needs a tune and minor things
02 Neon R/T ~ 08/08/08 -traded for the 07 Caliber R/T (03/14/11 -traded Caliber for STI)
---
http://www.st1ck3rs.com
http://www.detroitneonowners.org
Update Time Guys!
Got some more stuff worked out now! Pics follow...
Getting ready to do the axles:
Andrew checking the ugh...alignment of the axle :
Mocking up the interfooler:
Pretending to bolt it up after Jeff and I finished it:
New fuel pump from Aeromotive:
Custom built 3" downpipe:
Running the fuel lines and intake:
E-gay intake for 2.0L 2GN works great I think, I will add a 10" extension pipe that will come out the headlight hole for racing:
Needed to trim a little to clear the PCV and Thermo housing:
More updates tomorrow hopefully guys!
Got some more stuff worked out now! Pics follow...
Getting ready to do the axles:
Andrew checking the ugh...alignment of the axle :
Mocking up the interfooler:
Pretending to bolt it up after Jeff and I finished it:
New fuel pump from Aeromotive:
Custom built 3" downpipe:
Running the fuel lines and intake:
E-gay intake for 2.0L 2GN works great I think, I will add a 10" extension pipe that will come out the headlight hole for racing:
Needed to trim a little to clear the PCV and Thermo housing:
More updates tomorrow hopefully guys!
-> Chris <-
1998 SRT Swap Drag Car / 1997 Dodge Neon Coupe
1998 SRT Swap Drag Car / 1997 Dodge Neon Coupe
Victoria Day Updates:
Since today is a holiday in the Great White North, we got a little more done today. Took the time to clean up some stuff and get it rolling for now.
Got a set of headlights mounted, the side markers and bumper on, as well as some hubcaps for the sleeper look
Intercooler is all mounted, trimmed back the bumper to get it to fit better, and get a little more air to it.
Cleaned up the underside of the hood and the bay.
Continued gutting the interior and vaccuumed it all out, need to find a seat for it...
And for all the haters, I needed to do this, just to get all the hot air out from the turbo without melting my cowl.
Still want to do some fixes to the body, there is a fair share of dings for an 11 year old car, so there is some paint touch up to do as well as a few nicks to fix, but she's coming along.
Our MS is almost ready, just waiting on a few things first then we will work on getting that in.
Since today is a holiday in the Great White North, we got a little more done today. Took the time to clean up some stuff and get it rolling for now.
Got a set of headlights mounted, the side markers and bumper on, as well as some hubcaps for the sleeper look
Intercooler is all mounted, trimmed back the bumper to get it to fit better, and get a little more air to it.
Cleaned up the underside of the hood and the bay.
Continued gutting the interior and vaccuumed it all out, need to find a seat for it...
And for all the haters, I needed to do this, just to get all the hot air out from the turbo without melting my cowl.
Still want to do some fixes to the body, there is a fair share of dings for an 11 year old car, so there is some paint touch up to do as well as a few nicks to fix, but she's coming along.
Our MS is almost ready, just waiting on a few things first then we will work on getting that in.
-> Chris <-
1998 SRT Swap Drag Car / 1997 Dodge Neon Coupe
1998 SRT Swap Drag Car / 1997 Dodge Neon Coupe
- Ladi3sman55
- 1GN Registrant
- Posts: 2895
- Joined: Tue May 15, 2007 5:30 pm
- Location: 51106
- Contact:
lookin good i dig the hood tilt btw!
jw why did you remove the bracing on the hood?
jw why did you remove the bracing on the hood?
The definition of a NEON
A great domestic compact car whose rapidly disappearing taillights are most typically seen through the windshields of Honda Civics, Chevy Cavaliers, and other assorted shitboxes.
According to Urban Dict. dot COM
- silversport
- 1GN Registrant
- Posts: 34
- Joined: Sat Mar 31, 2007 11:21 am
- Location: Aurora, Ontario
- silversport
- 1GN Registrant
- Posts: 34
- Joined: Sat Mar 31, 2007 11:21 am
- Location: Aurora, Ontario