xxr 002
Posted: Sun Oct 23, 2011 3:59 pm
will 16x7 inch xxr's fit?
Page 1 of 1
Posted: Sun Oct 23, 2011 5:45 pm
depends on the bolt pattern and offset. without those, its hard to say
Posted: Fri Oct 28, 2011 9:02 pm
Wheel Size- 16x8
Bolt Pattern- Universal 5 Lug
Offset- +0
Backspacing- 4.5
Lip Depth- 3.5"
Centerbore- 73.1
Bolt Pattern- Universal 5 Lug
Offset- +0
Backspacing- 4.5
Lip Depth- 3.5"
Centerbore- 73.1
Posted: Sat Oct 29, 2011 2:18 am
I'm not sure about the centerbore, I don't remember what ours is. The rest sounds like it should fit, no? I'm not sure if your car is lowered or not. I think with a lowered car, you need to bring the wheel in some more. The backspacing sounds right too. I'm pretty sure I remember the maximum back spacing being 5.5" or so.
Posted: Sat Oct 29, 2011 11:42 am
its lowered like an inch and a half, but i've got those el cheapo coilovers that slide over your shocks. so im gonna put those on to get the look i want. i was just wondering if they would fit and not stick way outside they fender and make it look real goofy, or if i will have to roll them
Posted: Sun Oct 30, 2011 8:52 pm
The xxr's with a zero offset will not work with extensive fender work.
Posted: Sun Oct 30, 2011 8:55 pm
srtdreamin wrote:The xxr's with a zero offset will not work with extensivefender work.
Posted: Sun Oct 30, 2011 9:34 pm
they will or wont?
Posted: Sun Oct 30, 2011 9:43 pm
With stock springs they will rub a tiny bit. But with any drop what so ever ur going to have to do extensive fender rollin/stretching..
Posted: Mon Oct 31, 2011 11:24 pm
That's exactly what I was thinkingsrtdreamin wrote:With stock springs they will rub a tiny bit. But with any drop what so ever ur going to have to do extensive fender rollin/stretching..
Posted: Tue Nov 01, 2011 8:05 am
Well i just read ur post again..and u stated that u wanted to run 16x7 with 0 offset. Truthfully i dont kow about them.. i was assuming u want the look like the pic i posted of the red coupe. Those are the 16x8 with a 0 offset..and yes fender work and stretching was involved in that car.
Posted: Sat Nov 05, 2011 10:50 am
Yeah i want the 16x8. I love the look of the stupid low offset wheels. There is a whit neon on the org and its got 16x8 and is dumped! It doesnt look like it has any fender work done. Maybe minimal in the front but i know none in the back. I think its dragneons
Posted: Tue Nov 08, 2011 7:42 am
Yah i know the car u speaking of..and yes he does have a great deal of fender work in the front and rear...anyway i hope all these post help u.
Posted: Wed Nov 09, 2011 7:35 am
It ALLLL depends on how low you are. 16x8's 0 offset will fit on a neon with no to slight lowering. If you want to tuck tires like the car posted above, then you will need the fenders rolled and possibly trimmed on the inside.
Posted: Wed Nov 16, 2011 3:29 pm
this is exactly what i wanted to read. i looking into xxr 522 16X8's . Love how these cars looked dumped.