trailing arm problems

Have some questions about how to achive better handling and stopping power? Questions about 1st gen Neon suspension, steering and braking systems belong right here!
Post Reply
97sohc10
1GN Registrant
Posts: 66
Joined: Tue Dec 21, 2010 10:21 pm
Location: hanover pa

trailing arm problems

Post by 97sohc10 » Tue Oct 25, 2011 8:04 am

ok so i just had a full alignment done and when they went to adjust the rear toe one of the bolts broke off is there any where that sell a new bolt kits or are their places that make after market
id much rather buy aftermarket if i could?

2drSRT4
1GN Registrant
Posts: 853
Joined: Mon Feb 28, 2011 7:12 pm
Location: El Paso, TX

Post by 2drSRT4 » Tue Oct 25, 2011 9:23 pm

Any bolt will work, as long as it's the right size. Go to a hardware store with the broken bolt and have one made.
Image
Image

jamieely
1GN Registrant
Posts: 429
Joined: Tue Feb 10, 2009 12:39 pm
Location: Greenwood, IN

Post by jamieely » Tue Oct 25, 2011 9:51 pm

Make sure you get a grade 8 or 10.9.
1995 Highline Coupe SOHC MTX.
DOHC Mopar PCM
e85, 30lb injectors, LM-1, SAFC
Custom CAI, 60mm MPx TB, AMM Box Intake, DOHC pistons, built4race UDP
PT Clutch, 3.94 FD
AF/X LTH, High Flow Cat, Spiral Flow, 2.5" piping, Flowmaster 80 series

P&P Magnum head, Crane springs, Crane 007, AEM 3-bolt cam gear almost ready to bolt on

2drSRT4
1GN Registrant
Posts: 853
Joined: Mon Feb 28, 2011 7:12 pm
Location: El Paso, TX

Post by 2drSRT4 » Tue Oct 25, 2011 10:55 pm

Thanks, Jamie. Forgot to add that in
Image
Image

97sohc10
1GN Registrant
Posts: 66
Joined: Tue Dec 21, 2010 10:21 pm
Location: hanover pa

Post by 97sohc10 » Wed Oct 26, 2011 10:30 am

well ive tried everywhere possible except fastnal and the only i can do is buy a box of ten at a time

2drSRT4
1GN Registrant
Posts: 853
Joined: Mon Feb 28, 2011 7:12 pm
Location: El Paso, TX

Post by 2drSRT4 » Wed Oct 26, 2011 12:13 pm

Ah, that sucks lol
Image
Image

robert 'bob' paulson
1GN Registrant
Posts: 829
Joined: Sun Jan 28, 2007 7:18 pm
Location: Elmira Heights, NY

Post by robert 'bob' paulson » Wed Oct 26, 2011 4:08 pm

97sohc10 wrote:well ive tried everywhere possible except fastnal and the only i can do is buy a box of ten at a time
did you try Lowes and Farm & Tractor Supply? between those two stores, i've been able to replace just about any bolt i've needed for all my vehicles. like mentioned, for suspension parts you should try to get at least Grade 8.

Gim H3ll
1GN Registrant
Posts: 69
Joined: Wed Feb 23, 2011 12:26 pm
Location: Akron,Ohio

Post by Gim H3ll » Wed Oct 26, 2011 6:23 pm

Sears hardware has all the stuff for my car.
1998 4dr SOHC neon Iceman intake

97sohc10
1GN Registrant
Posts: 66
Joined: Tue Dec 21, 2010 10:21 pm
Location: hanover pa

Post by 97sohc10 » Thu Oct 27, 2011 8:44 am

ill have to go check them out today yet

97sohc10
1GN Registrant
Posts: 66
Joined: Tue Dec 21, 2010 10:21 pm
Location: hanover pa

Post by 97sohc10 » Thu Oct 27, 2011 9:29 am

just went to all three place lowes tractor supply sears and fastnal only pleace that could even get them was fastnal and they were like 20 bucks per bolt is there a place that makes after lateral links

Post Reply