Search found 672 matches

by infil
Wed Feb 06, 2008 5:34 pm
Forum: General 1st Gen Discussion
Topic: ya think i got a leaking headgasket
Replies: 7
Views: 2677

john?
by infil
Tue Feb 05, 2008 8:27 pm
Forum: Engine
Topic: cam installation
Replies: 16
Views: 4923

i cant think of an ohc engine for a while thats used cam bearings.
by infil
Fri Feb 01, 2008 6:35 pm
Forum: General 1st Gen Discussion
Topic: Holy S***...... help!
Replies: 15
Views: 4680

you should still have continuity between the pcm, pdc and connectors with the green/orange wire.
by infil
Thu Jan 31, 2008 6:19 pm
Forum: General 1st Gen Discussion
Topic: Catalytic Converter?
Replies: 23
Views: 6329

fwiw our metal guy gives anywhere between 40-80 per cat.
by infil
Thu Jan 31, 2008 6:18 pm
Forum: General 1st Gen Discussion
Topic: Holy S***...... help!
Replies: 15
Views: 4680

sounds like a ground problem. pin out the green/orange and black/blue wires from the connectors to the pcm terminal.
by infil
Thu Jan 31, 2008 1:26 pm
Forum: General 1st Gen Discussion
Topic: Catalytic Converter?
Replies: 23
Views: 6329

going by the federal laws governing emissions, it is technically illegal to service a cat that is not in a state of failure. selling a used cat is illegal, as well. its also a federal standard that a cat can be no more than 10% of total exhaust system backpressure. Best street/track setup IMO with a...
by infil
Wed Jan 30, 2008 9:41 pm
Forum: General 1st Gen Discussion
Topic: Catalytic Converter?
Replies: 23
Views: 6329

oe/high quality cats use a coating of platinum over the element. cats are worth a ton for that reason.
by infil
Tue Jan 29, 2008 8:44 pm
Forum: Engine
Topic: Misfire code 43. What should I do?
Replies: 15
Views: 10036

all codes will repeat themselves if they are set for more than three drive cycles.
After three they go into memory as a history code, but if they are still setting they'll stay resident in both history and as a pending code.
by infil
Tue Jan 29, 2008 8:38 pm
Forum: General 1st Gen Discussion
Topic: show me where to find
Replies: 16
Views: 5003

4gauge is fine, just get quality stuff.
by infil
Mon Jan 28, 2008 7:16 pm
Forum: Engine
Topic: Odd Noise...I need some help
Replies: 14
Views: 5221

what kind of oil came out and what went back in?
by infil
Mon Jan 28, 2008 7:15 pm
Forum: Engine
Topic: Misfire code 43. What should I do?
Replies: 15
Views: 10036

lol $11 plugs and wires? that scares me lol. FWIW throwing parts at a car till the problem disappears is a generally expensive way to do it. I completely agree with test the stuff nad find the actual problem as opposed to throwing parts at it. rust on the coil probably either bad boot ont he coil si...
by infil
Sun Jan 27, 2008 9:07 am
Forum: General 1st Gen Discussion
Topic: oh this sucks, and could be dead already :(
Replies: 31
Views: 7587

i have to agree the shop isn't at fault. what would you have said if a coolant flush turned into an $800+ head gasket? I know for a fact a head gasket on a belt driven engine doesnt' generally get done without tbelt, water pump etc. it doesn't pay to have all of it apart and not replace something li...
by infil
Wed Jan 23, 2008 8:19 pm
Forum: Naturally Aspirated
Topic: weight redux.
Replies: 49
Views: 30134

dryus iceus?
by infil
Mon Jan 21, 2008 3:08 pm
Forum: Naturally Aspirated
Topic: weight redux.
Replies: 49
Views: 30134

dont lick it
by infil
Mon Jan 21, 2008 3:07 pm
Forum: General 1st Gen Discussion
Topic: Oil leak ! Rhaa !
Replies: 14
Views: 4253

looks like a cam position sensor seal