1GN.ORG 1GN.ORG
get yer n00b on
 
 Watched TopicsWatched Topics   FAQFAQ  Forum RulesForum Rules   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 GarageGarage   1/4 Mile Table1/4 Mile Table   ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

UPDATE !!! Transmission Making Grinding Noises

Goto page 1, 2  Next
 
Post new topic   Reply to topic    1GN.ORG Forum Index -> Drivetrain
View previous topic :: View next topic  
Author Message
hotrod
1GN Neon Enthusiast
1GN Registrant


Age: 42
Joined: 30 Sep 2009
Posts: 180
Location: GREATER BAY AREA

1997 Dodge Neon

PostPosted: Sun Jan 30, 2011 2:05 pm    Post subject: UPDATE !!! Transmission Making Grinding Noises Reply with quote

Car In Neutral, with the Clutch up, my Trans makes a grinding noise, with Clutch down, the grinding noise stops, Ill get Video up soon, but what could be making my transmission do this, I have a new Throwout Bearing, + Clutch Installed, also my Trans was already making this noise, prior to the Clutch, & Throwout Bearing Replacement.
Quote:


I'm an Idiot, Grinding noise issue found an fixed, but I will not know for sure until I drive it for a while, the reason my trans was making those grinding noises, was that it only had 1 quart of fluid inside my trany Embarassed after draining what was left of fluid, I added 2 1/2 quarts of Redline MTL 13.95$ 1Quart Part#5204 from Winchester Auto, the grinding was completely gone. let hope my dumb ars didnt mess up anything inside trans by driving it like this lol

_________________
My Ne0n Project Can Be Found Here
http://teamtos.ca/forum/viewtopic.php?f=31&t=153

IT'S JUST A NEON L0oL...


Last edited by hotrod on Wed Mar 09, 2011 8:36 pm; edited 2 times in total
Back to top
View user's profile Send private message Visit poster's website  
1genRTturbo
1GN Registrant


Age: 35
Joined: 28 Feb 2010
Posts: 467
Location: Tooele, ut


PostPosted: Sun Jan 30, 2011 3:06 pm    Post subject: Reply with quote

hate to say it, t/o bearing might be in backwards, no good, or catastrophicly failing. rarely have i seen an input shaft bearing go bad, though it is possible.
_________________
It's not the fall that hurts, it's the sudden stop at the bottom!
Back to top
View user's profile Send private message AIM Address
hotrod
1GN Neon Enthusiast
1GN Registrant


Age: 42
Joined: 30 Sep 2009
Posts: 180
Location: GREATER BAY AREA

1997 Dodge Neon

PostPosted: Sun Jan 30, 2011 3:35 pm    Post subject: Reply with quote

hmmm... is this even possible, i thought they only let you install it one way, when i was installing mines, i put it in backwards the 1st time, and the tabs didn't line up properly, so i changed the mounting position, and the tabs lined up, so i mounted it that way. But the reason that i installed the new clutch and throwout bearing in the 1st place was to rid myself from that horrific grinding noise from trans...
_________________
My Ne0n Project Can Be Found Here
http://teamtos.ca/forum/viewtopic.php?f=31&t=153

IT'S JUST A NEON L0oL...
Back to top
View user's profile Send private message Visit poster's website  
1genRTturbo
1GN Registrant


Age: 35
Joined: 28 Feb 2010
Posts: 467
Location: Tooele, ut


PostPosted: Sun Jan 30, 2011 3:51 pm    Post subject: Reply with quote

possible, sure. plausible? not likely. i am a bit lost, might be a bearing failure.
_________________
It's not the fall that hurts, it's the sudden stop at the bottom!
Back to top
View user's profile Send private message AIM Address
2.4swapneon
1GN n00b


Age: 29
Joined: 15 Dec 2010
Posts: 8
Location: uniontown pa


PostPosted: Sun Jan 30, 2011 3:59 pm    Post subject: Reply with quote

ah i had the same problem before and what mine ended up being was that the tranny had cam lose and walked away from the motor.
_________________
97 2.4 swapped neon coupe
crower stage 2 cams springs and retainers
shaved 2.0 head
24lb injectors
mopar ecu
60 mm tb
Back to top
View user's profile Send private message Send e-mail  
Boostedpdx
1GN Registrant


Age: 34
Joined: 07 Nov 2009
Posts: 85
Location: Washington, USA


PostPosted: Sun Jan 30, 2011 4:14 pm    Post subject: Reply with quote

There is only one way to install the TOB, if you tried to install it backwards the tabs would be against the clutch pressure plate. Every neon i have owned had noisy TOB's even my srt4 was like this. Also can be the shifting linkage or forks, w/e you call them. Over long period of time and lots of miles they tend to rattle. Only way to fix those is a trans rebuild.
_________________

_____________________________________________
| Donate to nwneon.com | Project Log - 98 DOHC Expresso |
04 Srt-4 Stage II :Gone
99 R/t Hahn Stage II :Sold to 2themax
Back to top
View user's profile Send private message Visit poster's website  
hotrod
1GN Neon Enthusiast
1GN Registrant


Age: 42
Joined: 30 Sep 2009
Posts: 180
Location: GREATER BAY AREA

1997 Dodge Neon

PostPosted: Sun Jan 30, 2011 4:15 pm    Post subject: Reply with quote

now im lost lol
_________________
My Ne0n Project Can Be Found Here
http://teamtos.ca/forum/viewtopic.php?f=31&t=153

IT'S JUST A NEON L0oL...
Back to top
View user's profile Send private message Visit poster's website  
Boostedpdx
1GN Registrant


Age: 34
Joined: 07 Nov 2009
Posts: 85
Location: Washington, USA


PostPosted: Sun Jan 30, 2011 4:17 pm    Post subject: Reply with quote

You can check the shifting linkage, start the car up and go under the hood and hold the cables and linkage with your hand. You can wiggle them slightly, but be careful doing this, if you wiggle to hard and put it in gear the car is gonna hop over you. best to have a friend helping with that. If the rattle does not go away its time for a different TOB.
_________________

_____________________________________________
| Donate to nwneon.com | Project Log - 98 DOHC Expresso |
04 Srt-4 Stage II :Gone
99 R/t Hahn Stage II :Sold to 2themax
Back to top
View user's profile Send private message Visit poster's website  
hotrod
1GN Neon Enthusiast
1GN Registrant


Age: 42
Joined: 30 Sep 2009
Posts: 180
Location: GREATER BAY AREA

1997 Dodge Neon

PostPosted: Tue Feb 01, 2011 9:32 pm    Post subject: Reply with quote

well finally got video, & sound of trans Noise, the sound quality Isn't so good, but I hope you can hear it ok.

---> http://www.youtube.com/watch?v=256jxM9fNuk
_________________
My Ne0n Project Can Be Found Here
http://teamtos.ca/forum/viewtopic.php?f=31&t=153

IT'S JUST A NEON L0oL...
Back to top
View user's profile Send private message Visit poster's website  
Boostedpdx
1GN Registrant


Age: 34
Joined: 07 Nov 2009
Posts: 85
Location: Washington, USA


PostPosted: Tue Feb 01, 2011 10:34 pm    Post subject: Reply with quote

Definitely a TOB to Pressure plate issue. Sounds like the clutch fork might not be secured properly. Take the inspection cover off the top of the trans and watch the clutch fork. Does it vibrate aggressively?
_________________

_____________________________________________
| Donate to nwneon.com | Project Log - 98 DOHC Expresso |
04 Srt-4 Stage II :Gone
99 R/t Hahn Stage II :Sold to 2themax
Back to top
View user's profile Send private message Visit poster's website  
hotrod
1GN Neon Enthusiast
1GN Registrant


Age: 42
Joined: 30 Sep 2009
Posts: 180
Location: GREATER BAY AREA

1997 Dodge Neon

PostPosted: Sat Feb 05, 2011 8:15 am    Post subject: Reply with quote

Boostedpdx wrote:
Definitely a TOB to Pressure plate issue. Sounds like the clutch fork might not be secured properly. Take the inspection cover off the top of the trans and watch the clutch fork. Does it vibrate aggressively?


nope doesnt vibrate
_________________
My Ne0n Project Can Be Found Here
http://teamtos.ca/forum/viewtopic.php?f=31&t=153

IT'S JUST A NEON L0oL...
Back to top
View user's profile Send private message Visit poster's website  
hotrod
1GN Neon Enthusiast
1GN Registrant


Age: 42
Joined: 30 Sep 2009
Posts: 180
Location: GREATER BAY AREA

1997 Dodge Neon

PostPosted: Sun Feb 13, 2011 4:59 pm    Post subject: Reply with quote

Can Someone Explain to me, how to change the Input shaft bearing, on a 1997 dodge neon sohc manual transmission?
I have been doing alot of research on the grinding issue, of my trans. And have came to a conclusion, that I need to replace this bearing, basically if you push the clutch in, and the trans makes noise, its the throwout bearing, if you release the clutch, and the trans makes noise, its the input shaft bearing, and thats exactly what my trans is doing, when I push the clutch in, the noise goes away, after releasing the clutch, the noise returns...
_________________
My Ne0n Project Can Be Found Here
http://teamtos.ca/forum/viewtopic.php?f=31&t=153

IT'S JUST A NEON L0oL...
Back to top
View user's profile Send private message Visit poster's website  
hotrod
1GN Neon Enthusiast
1GN Registrant


Age: 42
Joined: 30 Sep 2009
Posts: 180
Location: GREATER BAY AREA

1997 Dodge Neon

PostPosted: Wed Mar 09, 2011 7:49 pm    Post subject: Transmission Making Grinding Noises Reply with quote

hotrod wrote:
Car In Neutral, with the Clutch up, my Trans makes a grinding noise, with Clutch down, the grinding noise stops, Ill get Video up soon, but what could be making my transmission do this, I have a new Throwout Bearing, + Clutch Installed, also my Trans was already making this noise, prior to the Clutch, & Throwout Bearing Replacement.

_________________
My Ne0n Project Can Be Found Here
http://teamtos.ca/forum/viewtopic.php?f=31&t=153

IT'S JUST A NEON L0oL...
Back to top
View user's profile Send private message Visit poster's website  
jacktimo
1GN Registrant


Age: 29
Joined: 04 Jul 2013
Posts: 17
Location: usa


PostPosted: Tue Oct 22, 2013 2:23 am    Post subject: Reply with quote

possible, sure. plausible? not likely. i am a bit lost, might be a bearing failure.




________________________________________________
Lassen Sie mir eine E-besessen Fußballspiel Fifa 14, enthält ein Next-Generation den Geist des sportlichen Wettkampf Meisterwerk! Können Sie genießen!(German)
FIFA Coins
Back to top
View user's profile Send private message  
jeekqing
fifa 15 coins
1GN n00b


Age: 27
Joined: 17 Nov 2014
Posts: 12
Location: KIU


PostPosted: Mon Nov 17, 2014 1:50 am    Post subject: Reply with quote

I very much agree with your point of view, the article is well written, like this one

well ,it is a good post ,i am sue you are a talent

______________________________
we like Fifa 15 coins without reason
Go to our home page:http://www.fifautc.co.uk/
Back to top
View user's profile Send private message  
Display posts from previous:   
Post new topic   Reply to topic    1GN.ORG Forum Index -> Drivetrain All times are GMT - 8 Hours
Goto page 1, 2  Next
Page 1 of 2

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



smartDark Style by Smartor
Powered by p h p B B © 2001 , 2005 p h p B B Group
Protected by Anti-Spam ACP
1GN.org