Swapping in the 95-99 2.4, answer's for your build
Swapping in the 95-99 2.4, answer's for your build
N/A Stand's for Natural Aspired - Meaning no turbo
Will SRT-4 Pistons fit in my N/A 2.4?
YES! Stock srt-4 pistons fit in a n/a 2.4 your block must have a good STOCK bore. The rods and pistons WILL fit in a N/A 2.4. The pistons from a srt-4 will drop compression to 8.1.1. The year of the block does not matter
Will the rod barrings work out of a SRT-4?
If your Crank is stock then you may use the stock barrings out of an SRT-4. The rods on a srt-4 have hole by the top of them for oil to come out of. srt-4 barrings also have this hole. N/A 2.4's do not! I would recomend using the srt-4 barring's if you are using srt-4 rods.. Though you do not have to use srt-4 barring's. The crank out of your N/A 2.4 will work fine with these rods.
Will the SRT-4 Crank work on my N/A 2.4?
The SRT-4 crank wont work on a 95-99 N/A 2.4 because of the Trigger wheel.
Will my 2.0 Crank work in a 2.4
Your 2.0 crank wont work on a 2.4.
How much can i get SRT-4 rods and pistons For?
Srt-4 rods and piston with rings will run around 100 a piece Depending on were you get them! The rod's and piston's are normally sold together. I would recomend getting ahold of some of the vender's on this site and SRTforums to get a good deal on rod's and piston's. These rods and pistons will also hold some serious HP right around 450-500Crank Hp
On the top is a stock N/A rod and on the bottom is a srt-4 rod
the srt-4 rod is also made from C-70 forged steel rather than the powdered-metal construction of the NA rods
Can i use SRT-4 rods with aftermarket piston?
Aftermarket pistons will fit a srt-4 rod.
so if your N/A needs bored buy aftermarket pistons to go with your srt-4 rods.
Can i use SRT-4 rod's and put higher comp pistons on them?
YES!!! Srt-4 rod's will go with any compression piston.
will a SRT-4 oil pump, Oil Pan, Pickuptube, Tensioner work with my N/A 2.4?
These to will work on your N/A 2.4 but they will need to be bought together. If you go this route you Must buy the pick up tube, tensioner,
oil pan, Oilpan Gasket. Also to make installation easy buy a srt-4 water-Pump.
You can get the GT Cruiser or the SRT-4 stuff. It will all work. The SRT-4 gasket comes with tabs like a crank scraper but does not effect the crank were the balance shafts are.
The oil pump out of the SRT-4 pumps 15cc of oil instead of 12cc.
It works better for a turbo app then the N/a 2.4 pump. Also i noticed that the srt-4 water pump look's like a better design then the N/A 2.4...
will a SRT-4 Turbo or exhaust work on my 1st gen?
IT DOES NOT MATTER IF YOU HAVE A 2.0 or 2.4SWAP.. YES The turbo bolts right up!
Any SRT-4 downpipe will work. you can use the SRT-4 exhaust with some mod's. This is a easy task...... you can also make your own.
What timing belt do i used on my 2.4 N/A?
When choosing a timing belt, it wont matter which one you choose as long as it's from a 2.4.. if you added all the srt-4 stuff it's still the same belt as the N/A belt.... SRT-4 Timing belt and N/A timing belt are the same!
can i use a SRT-4 Head on a 2001 and older block?
If your block is a 2001 and older you can use any head from 1995 - 2001
If your block is a 2002 and newer you need a 2002 - 2005 head
In the year 2002 they changed one oil port in the rear of the head so it will no longer bold on to a older block. How ever you can mod a 2002+newer head to work with a older style block!
will a SRT-4 headgasket fit a regular N/a 2.4?
The headgasket off an srt-4 will fit anything from 2002 and up.
it will not fit a 1995 - 2001 head do to the oil port change.
Use the gasket YEAR that goes with the block year
will a 95-99 2.0 DOHC Head fit my N/a 2.4?
YES this head will fit your 1995 - 2001 2.4 block... If Your block is a 2002 or newer it will not work..
Will my DOHC 2.0 cam gears work on my N/A 2.4
Stock 2.0 cam gears can be flipped over and they will work on your 2.4
to make After-market 2.0 cam gears work you will need to buy a spacer from (your gonna have to search for the person who make's these)
will 1995 - 2001 2.0 cam's work in my 1995 - 2001 2.4?
The magnets on srt-4 cams are in the same spot as a 2.0 cam... So for either of these cam's to work you must rotate the cam magnet 90 degrese clock wise...
SRT-4 Valve cover
It will fit with some small mods. there is a hole that don't line up if you got a 95-99 head. it will need to be plugged because dirt could get in your valve-train. Read about it here>>> http://forums.neons.org/viewtopic.php?t ... highlight=
Will my 95-99 neon tranny bolt up to my 2.4?
YES an 95-99 tranny (atx or mtx) will bolt up to your 2.4 some brackets dont fit but it holds just fine
Will my 95-99 PCM work on my 2.4
Yes but you will need to rewire a few things. this is vary easy to do
PARTS NUMBERS YOU WILL NEED WHEN BUILDING A 95-99 2.4 BLOCK WITH ALL SRT-4 PARTS
UNDERCONSTRUCTION
Rod Barings 5093448AB
Rod and piston 4884247AD <you need 4
Rings 5093441AA
Main barings 5012582AA
Oil Pan 4777991AA
Oil Pump 4884390AB
Oil Pump Pickup/Screen 4792304AC
Oil Pan Gasket 4777994AA
Oil Filter Connector 4777998AA
Oil Filter Connector Gasket 4884000AA
Oil Filter Connector Screw 6102041AA
Timing Belt 4621844
Timing Belt Tensioner 4781570AB
Idler Pully 4781569AB
Upper Gasket Set 5101787AA
Lower Gasket Set 5093452AA
How much am i looking at? If you get good deals and all parts are used probly 700. - 1500.
ALL PARTS NEW BUT BLOCK 1000. 2500.
Parts List Under Constuction
Used 2.4 Block 95-99? JunkYard 50-500 Neons.ORG 50-300 Shipping is usually $150-200
2.4 SRT-4 rods and piston - New ????? --Used - $75-150 srtforums.com or neons.org
2.4 Crank - New 180. --Used $75 - 100
2.4 or 2.0 Head - Used 75-300 --Used $250-400
Will my 2.4 pick up chicks?
Yes as long it runs well and has me in it! J/K
ill add more when i figure more out
Will SRT-4 Pistons fit in my N/A 2.4?
YES! Stock srt-4 pistons fit in a n/a 2.4 your block must have a good STOCK bore. The rods and pistons WILL fit in a N/A 2.4. The pistons from a srt-4 will drop compression to 8.1.1. The year of the block does not matter
Will the rod barrings work out of a SRT-4?
If your Crank is stock then you may use the stock barrings out of an SRT-4. The rods on a srt-4 have hole by the top of them for oil to come out of. srt-4 barrings also have this hole. N/A 2.4's do not! I would recomend using the srt-4 barring's if you are using srt-4 rods.. Though you do not have to use srt-4 barring's. The crank out of your N/A 2.4 will work fine with these rods.
Will the SRT-4 Crank work on my N/A 2.4?
The SRT-4 crank wont work on a 95-99 N/A 2.4 because of the Trigger wheel.
Will my 2.0 Crank work in a 2.4
Your 2.0 crank wont work on a 2.4.
How much can i get SRT-4 rods and pistons For?
Srt-4 rods and piston with rings will run around 100 a piece Depending on were you get them! The rod's and piston's are normally sold together. I would recomend getting ahold of some of the vender's on this site and SRTforums to get a good deal on rod's and piston's. These rods and pistons will also hold some serious HP right around 450-500Crank Hp
On the top is a stock N/A rod and on the bottom is a srt-4 rod
the srt-4 rod is also made from C-70 forged steel rather than the powdered-metal construction of the NA rods
Can i use SRT-4 rods with aftermarket piston?
Aftermarket pistons will fit a srt-4 rod.
so if your N/A needs bored buy aftermarket pistons to go with your srt-4 rods.
Can i use SRT-4 rod's and put higher comp pistons on them?
YES!!! Srt-4 rod's will go with any compression piston.
will a SRT-4 oil pump, Oil Pan, Pickuptube, Tensioner work with my N/A 2.4?
These to will work on your N/A 2.4 but they will need to be bought together. If you go this route you Must buy the pick up tube, tensioner,
oil pan, Oilpan Gasket. Also to make installation easy buy a srt-4 water-Pump.
You can get the GT Cruiser or the SRT-4 stuff. It will all work. The SRT-4 gasket comes with tabs like a crank scraper but does not effect the crank were the balance shafts are.
The oil pump out of the SRT-4 pumps 15cc of oil instead of 12cc.
It works better for a turbo app then the N/a 2.4 pump. Also i noticed that the srt-4 water pump look's like a better design then the N/A 2.4...
will a SRT-4 Turbo or exhaust work on my 1st gen?
IT DOES NOT MATTER IF YOU HAVE A 2.0 or 2.4SWAP.. YES The turbo bolts right up!
Any SRT-4 downpipe will work. you can use the SRT-4 exhaust with some mod's. This is a easy task...... you can also make your own.
What timing belt do i used on my 2.4 N/A?
When choosing a timing belt, it wont matter which one you choose as long as it's from a 2.4.. if you added all the srt-4 stuff it's still the same belt as the N/A belt.... SRT-4 Timing belt and N/A timing belt are the same!
can i use a SRT-4 Head on a 2001 and older block?
If your block is a 2001 and older you can use any head from 1995 - 2001
If your block is a 2002 and newer you need a 2002 - 2005 head
In the year 2002 they changed one oil port in the rear of the head so it will no longer bold on to a older block. How ever you can mod a 2002+newer head to work with a older style block!
will a SRT-4 headgasket fit a regular N/a 2.4?
The headgasket off an srt-4 will fit anything from 2002 and up.
it will not fit a 1995 - 2001 head do to the oil port change.
Use the gasket YEAR that goes with the block year
will a 95-99 2.0 DOHC Head fit my N/a 2.4?
YES this head will fit your 1995 - 2001 2.4 block... If Your block is a 2002 or newer it will not work..
Will my DOHC 2.0 cam gears work on my N/A 2.4
Stock 2.0 cam gears can be flipped over and they will work on your 2.4
to make After-market 2.0 cam gears work you will need to buy a spacer from (your gonna have to search for the person who make's these)
will 1995 - 2001 2.0 cam's work in my 1995 - 2001 2.4?
The magnets on srt-4 cams are in the same spot as a 2.0 cam... So for either of these cam's to work you must rotate the cam magnet 90 degrese clock wise...
SRT-4 Valve cover
It will fit with some small mods. there is a hole that don't line up if you got a 95-99 head. it will need to be plugged because dirt could get in your valve-train. Read about it here>>> http://forums.neons.org/viewtopic.php?t ... highlight=
Will my 95-99 neon tranny bolt up to my 2.4?
YES an 95-99 tranny (atx or mtx) will bolt up to your 2.4 some brackets dont fit but it holds just fine
Will my 95-99 PCM work on my 2.4
Yes but you will need to rewire a few things. this is vary easy to do
PARTS NUMBERS YOU WILL NEED WHEN BUILDING A 95-99 2.4 BLOCK WITH ALL SRT-4 PARTS
UNDERCONSTRUCTION
Rod Barings 5093448AB
Rod and piston 4884247AD <you need 4
Rings 5093441AA
Main barings 5012582AA
Oil Pan 4777991AA
Oil Pump 4884390AB
Oil Pump Pickup/Screen 4792304AC
Oil Pan Gasket 4777994AA
Oil Filter Connector 4777998AA
Oil Filter Connector Gasket 4884000AA
Oil Filter Connector Screw 6102041AA
Timing Belt 4621844
Timing Belt Tensioner 4781570AB
Idler Pully 4781569AB
Upper Gasket Set 5101787AA
Lower Gasket Set 5093452AA
How much am i looking at? If you get good deals and all parts are used probly 700. - 1500.
ALL PARTS NEW BUT BLOCK 1000. 2500.
Parts List Under Constuction
Used 2.4 Block 95-99? JunkYard 50-500 Neons.ORG 50-300 Shipping is usually $150-200
2.4 SRT-4 rods and piston - New ????? --Used - $75-150 srtforums.com or neons.org
2.4 Crank - New 180. --Used $75 - 100
2.4 or 2.0 Head - Used 75-300 --Used $250-400
Will my 2.4 pick up chicks?
Yes as long it runs well and has me in it! J/K
ill add more when i figure more out
- neon_freak
- 1GN Registrant
- Posts: 521
- Joined: Wed Feb 14, 2007 5:57 am
- Location: Fond Du Lac, WI
looks like a copy and paste from the big org
95 strawberry coupe mtx sohc
pacesetter header/catback, sts, boogers, 3.0, atx tb, ported intake, mp ecu, solid bobble strut, magnecor wires
98 white rt coupe mtx 2.4
mopar ecu, egr kit. ur street pulley, mpx 60mm, iceman, msd wires/coil, solid mounts, ractive header, vibrant muffler
old 2.0-145.4hp@6161rpm, 134.5tq@5218rpm
pacesetter header/catback, sts, boogers, 3.0, atx tb, ported intake, mp ecu, solid bobble strut, magnecor wires
98 white rt coupe mtx 2.4
mopar ecu, egr kit. ur street pulley, mpx 60mm, iceman, msd wires/coil, solid mounts, ractive header, vibrant muffler
old 2.0-145.4hp@6161rpm, 134.5tq@5218rpm
- neon_freak
- 1GN Registrant
- Posts: 521
- Joined: Wed Feb 14, 2007 5:57 am
- Location: Fond Du Lac, WI
learn how to spell bearing
95 strawberry coupe mtx sohc
pacesetter header/catback, sts, boogers, 3.0, atx tb, ported intake, mp ecu, solid bobble strut, magnecor wires
98 white rt coupe mtx 2.4
mopar ecu, egr kit. ur street pulley, mpx 60mm, iceman, msd wires/coil, solid mounts, ractive header, vibrant muffler
old 2.0-145.4hp@6161rpm, 134.5tq@5218rpm
pacesetter header/catback, sts, boogers, 3.0, atx tb, ported intake, mp ecu, solid bobble strut, magnecor wires
98 white rt coupe mtx 2.4
mopar ecu, egr kit. ur street pulley, mpx 60mm, iceman, msd wires/coil, solid mounts, ractive header, vibrant muffler
old 2.0-145.4hp@6161rpm, 134.5tq@5218rpm
- nuklhed074
- 1GN Registrant
- Posts: 136
- Joined: Wed Oct 21, 2009 8:28 pm
- Location: lima,OH harsville,TN
- 1genRTturbo
- 1GN Registrant
- Posts: 468
- Joined: Sun Feb 28, 2010 5:20 pm
- Location: Tooele, ut