need help with main rod bearings and piston rings asap
- 1stgenneon
- 1GN Registrant
- Posts: 28
- Joined: Mon May 16, 2011 6:22 pm
- Location: Fresno
need help with main rod bearings and piston rings asap
i have a 98 dodge neon dohc idk if the engine has ever bein rebuilt but i cracked it open and all apart and im trying to order a rering kit off ebay so i can rebuld it but idk what sizes to go with the piston ring size is 3.427cm and 3.334cm and rod bearings are 0.094cm and 0.060cm and main bearings are 2.074cm these are the closes readings i can get but idk if there standard or oversized but thats what in stuck on
Who did you buy the car from i know many of the socal and norcal members.
Straight from the Chrysler repair manuals
ENGINE 2.0L DOHC
Cylinder Block
Cylinder Bore Diameter . . . 87.4924 - 87.5076 mm
(3.4446 - 3.4452 in.)
Out-of-Round (Max.) . . . . . . . 0.051 mm (0.002 in.)
Taper (Max.) . . . . . . . . . . . . . 0.051 mm (0.002 in.)
Piston Rings
Ring Gap Top
Compression Ring . . . . . . . . . . . 0.23 - 0.52 mm
(0.009 - 0.020 in.)
Ring Gap 2nd
Compression Ring . . . . . . . . . . . 0.49 - 0.78 mm
(0.019 - 0.031 in.)
Ring Gap Oil Control
(Steel Rails) . . . . . . . . . . . . . . . . 0.23 - 0.66 mm
(0.009 - 0.026 in.)
Ring Side Clearance Both
Compression Rings . . . . . . . . 0.025 - 0.065 mm
(0.0010 - 0.0026 in.)
Oil Ring (Pack) . . . . . . . . . . . . . 0.004 - 0.178 mm
(0.0002 - 0.0070 in.)
Ring Width Compression
Rings . . . . . . 1.17 - 1.19 mm (0.046 - 0.047 in.)
Oil Ring (Pack) . . . . . . . . . . . . . 2.854 - 3.008 mm
(0.1124 - 0.1184 in.)
Straight from the Chrysler repair manuals
ENGINE 2.0L DOHC
Cylinder Block
Cylinder Bore Diameter . . . 87.4924 - 87.5076 mm
(3.4446 - 3.4452 in.)
Out-of-Round (Max.) . . . . . . . 0.051 mm (0.002 in.)
Taper (Max.) . . . . . . . . . . . . . 0.051 mm (0.002 in.)
Piston Rings
Ring Gap Top
Compression Ring . . . . . . . . . . . 0.23 - 0.52 mm
(0.009 - 0.020 in.)
Ring Gap 2nd
Compression Ring . . . . . . . . . . . 0.49 - 0.78 mm
(0.019 - 0.031 in.)
Ring Gap Oil Control
(Steel Rails) . . . . . . . . . . . . . . . . 0.23 - 0.66 mm
(0.009 - 0.026 in.)
Ring Side Clearance Both
Compression Rings . . . . . . . . 0.025 - 0.065 mm
(0.0010 - 0.0026 in.)
Oil Ring (Pack) . . . . . . . . . . . . . 0.004 - 0.178 mm
(0.0002 - 0.0070 in.)
Ring Width Compression
Rings . . . . . . 1.17 - 1.19 mm (0.046 - 0.047 in.)
Oil Ring (Pack) . . . . . . . . . . . . . 2.854 - 3.008 mm
(0.1124 - 0.1184 in.)
- 1stgenneon
- 1GN Registrant
- Posts: 28
- Joined: Mon May 16, 2011 6:22 pm
- Location: Fresno
- 1genRTturbo
- 1GN Registrant
- Posts: 468
- Joined: Sun Feb 28, 2010 5:20 pm
- Location: Tooele, ut
can you afford to have engine work done? such as a bit of machining? have the crank checked, and the block honed, if they are a good machinest, they will steer you straight instead of making you do all this work to a good block and crank.
It's not the fall that hurts, it's the sudden stop at the bottom!
- 1genRTturbo
- 1GN Registrant
- Posts: 468
- Joined: Sun Feb 28, 2010 5:20 pm
- Location: Tooele, ut