Search found 672 matches

by infil
Tue Nov 13, 2012 8:43 pm
Forum: WTB (Wanted to Buy)
Topic: Header.
Replies: 1
Views: 6198

i have a rusty step tube magnum header i came across in my shed sunday...has both o2's for a 95, 3" dump collector.
by infil
Tue Nov 13, 2012 8:42 pm
Forum: WTB (Wanted to Buy)
Topic: PS Pump Bracket needed asap
Replies: 0
Views: 5515

PS Pump Bracket needed asap

Hello,
I am looking for a 1g sohc PS Pump Bracket. The aluminum one on the back side of the pump and IIRC the ac compressor mount is part of this bracket as well.

Nearby staten island would be terrific but either way i need it asap.
by infil
Sat Oct 03, 2009 1:11 am
Forum: Electrical
Topic: engine harness question.
Replies: 7
Views: 10159

to run off the stock pcm yuo'd need ckp, cmp, ect, b1s1, b1s2, injectors, map, iat, coil, alt, starter and i believe thats it. can eliminate evap, knock, oil psi, egr etc
by infil
Sat Oct 03, 2009 1:09 am
Forum: Electrical
Topic: smaller battery...
Replies: 14
Views: 13121

dry cell will still require venting and a sealed/approved box to run at an nhra track. its a battery, period.

i ran a tractor battery in teh racecar for 3 years with zero probs on same battery. this car got used maybe 3 times a month on a busy month with a few starts here and there for tuning etc.
by infil
Sat Oct 03, 2009 1:06 am
Forum: General 1st Gen Discussion
Topic: Where can I get 30# injectors for a 98 DOHC ??
Replies: 13
Views: 12922

bosch and accel offer cv6 plugged injectors ;)
by infil
Sat Oct 03, 2009 1:05 am
Forum: Engine
Topic: SOHC to DOHC
Replies: 12
Views: 11796

for a shop to supply a harness youll be looking in the thousands. a replacement harness for a dohc fire rebuild i did was quoted at 1300 wholesale. extend the ect wiring and call it good, IIRC thats the only difference in the dohc/sohc harnesses.
by infil
Sat Oct 03, 2009 1:04 am
Forum: Engine
Topic: Crower Cams failure ?
Replies: 3
Views: 5008

sounds like a bunch of inclusions in a batch of castings. the pin is simply to align the gear only, it is in now way designed to hold the load of a running motor, if the gear is torqued down properly, it will not move, if the pin broke after the car was running, again the gear was loose. as far as t...
by infil
Sat Oct 03, 2009 1:01 am
Forum: Engine
Topic: timing belt tensioner failure?
Replies: 3
Views: 4926

as a rule of thumb i have always replaced the tensioner with the tbelt set and water pump, saves alot of potential problems.
by infil
Sat Oct 03, 2009 12:58 am
Forum: Parts For SALE
Topic: Lots of stuff for sale
Replies: 17
Views: 15877

heads were teh same 95-02. one bolt hole that was used on the 95s wasn't tapped on the rest.

jerry is excellent to do business with fwiw. couple transactions now and great experiences every time :)
by infil
Sat Oct 03, 2009 12:54 am
Forum: Parts For SALE
Topic: parting out, all must go
Replies: 36
Views: 30028

canada, pm sent
by infil
Sat Sep 26, 2009 1:17 pm
Forum: Parts For SALE
Topic: parting out, all must go
Replies: 36
Views: 30028

canada, i will find out today, i apologize, we had a slight housing crisis that we had to deal with and has taken up most of my time. UDP is sold to INVUJerry Axles are sold to Awsomeears Intake, TB, Fuel rail, Filter and that plumbing as well as PCM sold to Kyle Rest is still available. As i've sai...
by infil
Sun Sep 06, 2009 2:47 pm
Forum: General 1st Gen Discussion
Topic: air conditioning question
Replies: 7
Views: 7897

real world i've never seen pressures that high on anything that was working properly without a dual AC system.

My neon, blowing 38-45deg on a 90deg day is 36on the low and 190-210 on the high :) at idle, at 3500rpm 24 on the low and about 250-260 on the high.
by infil
Sun Sep 06, 2009 2:45 pm
Forum: Parts For SALE
Topic: throttle bodies, ignition coil MORE!!! short thorw!!!
Replies: 16
Views: 14478

side note, 3 of the intake manifolds are for 95 wiring with seperate map/iats, 1 is 96+ with 4wire map/iat sensor :)
by infil
Sun Sep 06, 2009 2:41 pm
Forum: Parts For SALE
Topic: parting out, all must go
Replies: 36
Views: 30028

ignition is now available again. Think i forgot to mention the screamin demon coil as well which i'm including. Box, tach adapters, TRC2 timing retard which is NIB, coil etc. I will also include the cutoff and top end toggles that I installed, the lower end limit will be up to you. I had mine wired ...
by infil
Wed Sep 02, 2009 2:24 am
Forum: Parts For SALE
Topic: Koni Blacks w/ACR springs - MD - $275
Replies: 4
Views: 5154

think dibs come w/ payment :D jerry lookin forward to seein ya again bro :) think i got some goodies for ya that i came across, top shecret kind of goodies :)